View source for ASUS P4C800-E Deluxe Build Tutorial/Infos

== /proc/interrupts ==
 
            CPU0       CPU1
   0:         44          0   IO-APIC-edge      timer
   1:        541          0   IO-APIC-edge      i8042
   8:          1          0   IO-APIC-edge      rtc0
   9:          0          0   IO-APIC-fasteoi   acpi
  14:         32          0   IO-APIC-edge      ata_piix
  15:          0          0   IO-APIC-edge      ata_piix
  16:          0          0   IO-APIC-fasteoi   uhci_hcd:usb2, uhci_hcd:usb5
  18:      20613          0   IO-APIC-fasteoi   uhci_hcd:usb4, eth0
  19:          0          0   IO-APIC-fasteoi   uhci_hcd:usb3
  20:          3          0   IO-APIC-fasteoi   ohci1394
  23:          0          0   IO-APIC-fasteoi   sata_promise, ehci_hcd:usb1
 NMI:          0          0   Non-maskable interrupts
 LOC:      98191      98167   Local timer interrupts
 RES:       3037       7015   Rescheduling interrupts
 CAL:         46         67   function call interrupts
 TLB:        215       1250   TLB shootdowns
 TRM:          0          0   Thermal event interrupts
 SPU:          0          0   Spurious interrupts
 ERR:          0
 MIS:          0
 
== getpir ==
 
 /* This file was generated by getpir.c, do not modify!
  * (but if you do, please run checkpir on it to verify)
  *
  * Contains the IRQ Routing Table dumped directly from your
  * memory, which BIOS sets up.
  *
  * Documentation at: http://www.microsoft.com/whdc/archive/pciirq.mspx
  */
 
 #ifdef GETPIR
 #include "pirq_routing.h"
 #else
 #include <arch/pirq_routing.h>
 #endif
 
 const struct irq_routing_table intel_irq_routing_table = {
 	PIRQ_SIGNATURE,  /* u32 signature */
 	PIRQ_VERSION,    /* u16 version   */
 	32+16*12,	 /* There can be total 12 devices on the bus */
 	0x00,		 /* Where the interrupt router lies (bus) */
 	(0x1f<<3)|0x0,   /* Where the interrupt router lies (dev) */
 	0,		 /* IRQs devoted exclusively to PCI usage */
 	0x8086,		 /* Vendor */
 	0x24d0,		 /* Device */
 	0,		 /* Crap (miniport) */
 	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
 	0x66,		 /* u8 checksum. This has to be set to some
 			    value that would give 0 after the sum of all
 			    bytes for this structure (including checksum) */
 	{
 		/* bus,     dev|fn,   {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap},  slot, rfu */
 		{0x00,(0x01<<3)|0x0, {{0x60, 0xdcf8}, {0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 		{0x03,(0x08<<3)|0x0, {{0x68, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 		{0x00,(0x1f<<3)|0x0, {{0x62, 0xdcf8}, {0x61, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 		{0x00,(0x1d<<3)|0x0, {{0x60, 0xdcf8}, {0x63, 0xdcf8}, {0x62, 0xdcf8}, {0x6b, 0x0dcf8}}, 0x0, 0x0},
 		{0x03,(0x09<<3)|0x0, {{0x69, 0xdcf8}, {0x6a, 0xdcf8}, {0x6b, 0xdcf8}, {0x68, 0x0dcf8}}, 0x1, 0x0},
 		{0x03,(0x0a<<3)|0x0, {{0x6a, 0xdcf8}, {0x6b, 0xdcf8}, {0x68, 0xdcf8}, {0x69, 0x0dcf8}}, 0x2, 0x0},
 		{0x03,(0x0b<<3)|0x0, {{0x6b, 0xdcf8}, {0x68, 0xdcf8}, {0x69, 0xdcf8}, {0x6a, 0x0dcf8}}, 0x3, 0x0},
 		{0x02,(0x01<<3)|0x0, {{0x62, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 		{0x03,(0x0c<<3)|0x0, {{0x68, 0xdcf8}, {0x69, 0xdcf8}, {0x6a, 0xdcf8}, {0x6b, 0x0dcf8}}, 0x4, 0x0},
 		{0x03,(0x0d<<3)|0x0, {{0x69, 0xdcf8}, {0x6a, 0xdcf8}, {0x6b, 0xdcf8}, {0x68, 0x0dcf8}}, 0x5, 0x0},
 		{0x03,(0x03<<3)|0x0, {{0x68, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 		{0x03,(0x04<<3)|0x0, {{0x6b, 0xdcf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
 	}
 };
 
 unsigned long write_pirq_routing_table(unsigned long addr)
 {
 	return copy_pirq_routing_table(addr);
 }
 
== mptable ==
 
 /* generated by MPTable, version 2.0.15*/
 /* as modified by RGM for coreboot */
 #include <console/console.h>
 #include <arch/smp/mpspec.h>
 #include <device/pci.h>
 #include <string.h>
 #include <stdint.h>
 
 void *smp_write_config_table(void *v)
 {
         static const char sig[4] = "PCMP";
         static const char oem[8] = "LNXI    ";
         static const char productid[12] = "P4DPE       ";
         struct mp_config_table *mc;
 
         mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
         memset(mc, 0, sizeof(*mc));
 
         memcpy(mc->mpc_signature, sig, sizeof(sig));
         mc->mpc_length = sizeof(*mc); /* initially just the header */
         mc->mpc_spec = 0x04;
         mc->mpc_checksum = 0; /* not yet computed */
         memcpy(mc->mpc_oem, oem, sizeof(oem));
         memcpy(mc->mpc_productid, productid, sizeof(productid));
         mc->mpc_oemptr = 0;
         mc->mpc_oemsize = 0;
         mc->mpc_entry_count = 0; /* No entries yet... */
         mc->mpc_lapic = LAPIC_ADDR;
         mc->mpe_length = 0;
         mc->mpe_checksum = 0;
         mc->reserved = 0;
 
         smp_write_processors(mc);
 
 
 /*Bus:		Bus ID	Type*/
 	smp_write_bus(mc, 0, "PCI   ");
 	smp_write_bus(mc, 1, "PCI   ");
 	smp_write_bus(mc, 2, "PCI   ");
 	smp_write_bus(mc, 3, "PCI   ");
 	smp_write_bus(mc, 4, "ISA   ");
 /*I/O APICs:	APIC ID	Version	State		Address*/
 	smp_write_ioapic(mc, 2, 0x20, 0xfec00000);
 	{
 		device_t dev;
 		struct resource *res;
 		dev = dev_find_slot(1, PCI_DEVFN(0x1e,0));
 		if (dev) {
 			res = find_resource(dev, PCI_BASE_ADDRESS_0);
 			if (res) {
 				smp_write_ioapic(mc, 3, 0x20, res->base);
 			}
 		}
 		dev = dev_find_slot(1, PCI_DEVFN(0x1c,0));
 		if (dev) {
 			res = find_resource(dev, PCI_BASE_ADDRESS_0);
 			if (res) {
 				smp_write_ioapic(mc, 4, 0x20, res->base);
 			}
 		}
                 dev = dev_find_slot(4, PCI_DEVFN(0x1e,0));
                 if (dev) {
 			res = find_resource(dev, PCI_BASE_ADDRESS_0);
 			if (res) {
 				smp_write_ioapic(mc, 5, 0x20, res->base);
 			}
                 }
                 dev = dev_find_slot(4, PCI_DEVFN(0x1c,0));
                 if (dev) {
 			res = find_resource(dev, PCI_BASE_ADDRESS_0);
 			if (res) {
 				smp_write_ioapic(mc, 8, 0x20, res->base);
 			}
                 }
 	}
 /*I/O Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#
 */	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x0, 0x2, 0x0);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x1, 0x2, 0x1);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x0, 0x2, 0x2);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x3, 0x2, 0x3);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x4, 0x2, 0x4);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x6, 0x2, 0x6);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x7, 0x2, 0x7);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, 0x4, 0x8, 0x2, 0x8);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0x9, 0x2, 0x9);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0xc, 0x2, 0xc);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0xd, 0x2, 0xd);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0xe, 0x2, 0xe);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x4, 0xf, 0x2, 0xf);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x1, 0x0, 0x2, 0x10);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7c, 0x2, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x7d, 0x2, 0x11);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x74, 0x2, 0x10);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x75, 0x2, 0x13);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x76, 0x2, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x0, 0x77, 0x2, 0x17);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x2, 0x4, 0x2, 0x12);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, 0xc, 0x2, 0x14);
 	smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, 0x3, 0x10, 0x2, 0x17);
 /*Local Ints:	Type	Polarity    Trigger	Bus ID	 IRQ	APIC ID	PIN#*/
 	smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x0, 0x0, MP_APIC_ALL, 0x0);
 	smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_DEFAULT|MP_IRQ_POLARITY_DEFAULT, 0x0, 0x0, MP_APIC_ALL, 0x1);
 MP Config Extended Table Entries:
 
 --
 System Address Space
  bus ID: 0 address type: I/O address
  address base: 0xb000
  address range: 0x4000
 --
 System Address Space
  bus ID: 0 address type: I/O address
  address base: 0x0
  address range: 0x100
 --
 System Address Space
  bus ID: 0 address type: memory address
  address base: 0xa0000
  address range: 0x20000
 --
 System Address Space
  bus ID: 0 address type: memory address
  address base: 0xfe800000
  address range: 0x400000
 --
 System Address Space
  bus ID: 0 address type: prefetch address
  address base: 0xd7f00000
  address range: 0x20100000
 --
 Bus Heirarchy
  bus ID: 4 bus info: 0x01 parent bus ID: 0--
 Compatibility Bus Address
  bus ID: 0 address modifier: add
  predefined range: 0x00000000--
 Compatibility Bus Address
  bus ID: 0 address modifier: add
  predefined range: 0x00000001	/* There is no extension information... */
 
 	/* Compute the checksums */
 	mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
 	mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
 	printk_debug("Wrote the mp table end at: %p - %p\n",
 		mc, smp_next_mpe_entry(mc));
 	return smp_next_mpe_entry(mc);
 }
 
 unsigned long write_smp_table(unsigned long addr)
 {
 	void *v;
 	v = smp_write_floating_table(addr);
 	return (unsigned long)smp_write_config_table(v);
 }
 
== superiotool -dV ==
 
 superiotool r
 Probing for ALi Super I/O at 0x3f0...
   Failed. Returned data: id=0xffff, rev=0xff
 Probing for ALi Super I/O at 0x370...
   Failed. Returned data: id=0xffff, rev=0xff
 Probing for Fintek Super I/O at 0x2e...
   Failed. Returned data: vid=0x42fe, id=0x8282
 Probing for Fintek Super I/O at 0x4e...
   Failed. Returned data: vid=0xffff, id=0xffff
 Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x2e...
   Failed. Returned data: id=0xffff, rev=0xf
 Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
   Failed. Returned data: id=0x8282, rev=0xf
 Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
 Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
 Probing for NSC Super I/O at 0x2e...
   Failed. Returned data: port=0xff, port+1=0xff
 Probing for NSC Super I/O at 0x4e...
   Failed. Returned data: port=0xff, port+1=0xff
 Probing for NSC Super I/O at 0x15c...
   Failed. Returned data: port=0xff, port+1=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
   Failed. Returned data: id=0xff, rev=0xff
 Probing for Winbond Super I/O (init=0x88) at 0x2e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x89) at 0x2e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
 Found Winbond W83627THF/THG (id=0x82, rev=0x82) at 0x2e
 Register dump:
 idx 20 21 22 23 24 25 26 28  29 2a 2b 2c 2d 2e 2f
 val 82 82 ff fe 42 00 00 00  00 00 10 00 00 00 ff
 def 82 NA ff 00 MM 00 MM 00  00 00 MM MM MM 00 00
 LDN 0x00 (Floppy)
 idx 30 60 61 70 74 f0 f1 f2  f4 f5
 val 00 03 f0 06 02 0e 00 ff  00 00
 def 01 03 f0 06 02 0e 00 ff  00 00
 LDN 0x01 (Parallel port)
 idx 30 60 61 70 74 f0
 val 01 03 78 07 03 3a
 def 01 03 78 07 04 3f
 LDN 0x02 (COM1)
 idx 30 60 61 70 f0
 val 01 03 f8 04 00
 def 01 03 f8 04 00
 LDN 0x03 (COM2)
 idx 30 60 61 70 f0 f1
 val 01 02 f8 03 00 00
 def 01 02 f8 03 00 00
 LDN 0x05 (Keyboard)
 idx 30 60 61 62 63 70 72 f0
 val 01 00 60 00 64 01 0c 42
 def 01 00 60 00 64 01 0c 80
 LDN 0x07 (GPIO 1, GPIO 5, game port, MIDI port)
 idx 30 60 61 62 63 70 f0 f1  f2 f3 f4 f5
 val 08 02 01 03 30 00 ff ff  ff ff cd 00
 def 00 02 01 03 30 09 ff 00  00 ff 00 00
 LDN 0x08 (GPIO 2)
 idx 30 f0 f1 f2 f3 f4 f5 f6  f7
 val 00 ff ff ff 00 ff 00 00  00
 def 00 ff 00 00 00 RR 00 00  00
 LDN 0x09 (GPIO 3, GPIO 4)
 idx 30 f0 f1 f2 f3 f4 f5 f6
 val 03 ef 5f 00 00 df 01 00
 def 00 ff 00 00 00 ff 00 00
 LDN 0x0a (ACPI)
 idx 30 70 e0 e1 e2 e3 e4 e5  e6 e7 f0 f1 f3 f4 f6 f7  f9 fe ff
 val 00 00 00 00 ff 26 00 00  00 00 00 8f 30 00 00 00  00 00 00
 def 00 00 00 00 MM MM 00 00  00 00 00 00 00 00 00 00  00 RR RR
 LDN 0x0b (Hardware monitor)
 idx 30 60 61 70
 val 01 02 90 00
 def 00 00 00 00
 Probing for Winbond Super I/O (init=0x88) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x89) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x88) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x89) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x88) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x89) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x88) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x89) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
 
== flashrom -V ==
 
 Calibrating delay loop... 784M loops per second, 100 myus = 220 us. OK.
 No coreboot table found.
 Found chipset "Intel ICH5/ICH5R", enabling flash write... 
 BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0
 OK.
 Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff
 Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
 Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
 Probing for ASD AE49F2008, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Atmel AT49F002(N), 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Atmel AT25DF321, 4096 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for AMIC A25L40P, 512 KB: 4b ID not supported on this SPI controller
 Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0x9d, id2 0x6e
 Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0x9d, id2 0x6e
 Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
 Probing for AMIC A49LF040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for EMST F49B002UA, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff
 Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff
 Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff
 Probing for Macronix MX25L4005, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Macronix MX25L8005, 1024 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Macronix MX25L1605, 2048 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Macronix MX25L3205, 4096 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Macronix MX29F002, 256 KB: probe_29f002: id1 0x9d, id2 0x6e
 Probing for PMC Pm25LV010, 128 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm25LV016B, 2048 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm25LV020, 256 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm25LV040, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm25LV080B, 1024 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm25LV512, 64 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC Pm49FL002, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for PMC Pm49FL004, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Found chip "PMC Pm49FL004" (512 KB) at physical address 0xfff80000.
 Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0xff, id2 0xff
 Probing for Spansion S25FL016A, 2048 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for SST SST25VF016B, 2048 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for SST SST25VF040B, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0xff, id2 0xff
 Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST29EE020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF002A/B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF003A/B, 384 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF004A/B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0xff, id2 0xff
 Probing for SST SST49LF008A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation
 Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0xff, id2 0xff
 Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
 Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SST SST49LF080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation
 Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
 Probing for ST M25P05-A, 64 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P10-A, 128 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P20, 256 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P40, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P40-old, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P80, 1024 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P16, 2048 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P32, 4096 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P64, 8192 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M25P128, 16384 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST M29F002B, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for ST M29F002T/NT, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
 Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff
 Probing for ST M29W010B, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for ST M29W040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0x9d, id2 0x6e
 Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0x9d, id2 0x6e
 Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff
 Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0xff, id2 0xff
 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff
 Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff
 Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff
 Probing for ST M50LPW116, 2048 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation
 Probing for SyncMOS S29C31004T, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SyncMOS S29C51001T, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SyncMOS S29C51002T, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for SyncMOS S29C51004T, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W25x10, 128 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Winbond W25x20, 256 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Winbond W25x40, 512 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Winbond W25x80, 1024 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Winbond W29C011, 128 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W29EE011, 128 KB: 
 ===
   Probing disabled for Winbond W29EE011 because the probing sequence puts the
   AMIC A49LF040A in a funky state.
   Use 'flashrom -c W29EE011' if you have a board with this chip.
 ===
 Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0x9d, id2 0x6e
 Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0xff, id2 0xff, id1 parity violation
 Probing for Winbond W49F002U, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W49V002FA, 256 KB: probe_jedec: id1 0x9d, id2 0x6e
 Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: vid 0xff, did 0xff
 Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: vid 0x9d, did 0x6e
 Probing for EON unknown EON SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for Macronix unknown Macronix SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for PMC unknown PMC SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for SST unknown SST SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected
 Probing for ST unknown ST SPI chip, 0 KB: spi_command called, but no SPI chipset/strapping detected
 No operations were specified.
 
== lspci -tnvv ==
 
 -[0000:00]-+-00.0  8086:2578
            +-01.0-[0000:01]--+-00.0  1002:4e45
            |                 \-00.1  1002:4e65
            +-03.0-[0000:02]----01.0  8086:1019
            +-1d.0  8086:24d2
            +-1d.1  8086:24d4
            +-1d.2  8086:24d7
            +-1d.3  8086:24de
            +-1d.7  8086:24dd
            +-1e.0-[0000:03]--+-03.0  1106:3044
            |                 \-04.0  105a:3373
            +-1f.0  8086:24d0
            +-1f.1  8086:24db
            +-1f.3  8086:24d3
            \-1f.5  8086:24d5
 
== lspci -vvvxx ==
 
 00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller Hub (rev 02)
 	Subsystem: ASUSTeK Computer Inc. Unknown device 80f6
 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
 	Latency: 0
 	Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
 	Capabilities: [e4] Vendor Specific Information
 	Capabilities: [a0] AGP version 3.0
 		Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
 		Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
 00: 86 80 78 25 06 00 90 20 02 00 00 06 00 00 00 00
 10: 08 00 00 f8 00 00 00 00 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f6 80
 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
 
 00:01.0 PCI bridge: Intel Corporation 82875P Processor to AGP Controller (rev 02) (prog-if 00 [Normal decode])
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 64
 	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
 	I/O behind bridge: 0000b000-0000bfff
 	Memory behind bridge: fe800000-fe8fffff
 	Prefetchable memory behind bridge: d7f00000-f7efffff
 	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
 00: 86 80 79 25 07 01 a0 00 02 00 04 06 00 40 01 00
 10: 00 00 00 00 00 00 00 00 00 01 01 40 b0 b0 a0 02
 20: 80 fe 80 fe f0 d7 e0 f7 00 00 00 00 00 00 00 00
 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 00
 
 00:03.0 PCI bridge: Intel Corporation 82875P/E7210 Processor to PCI to CSA Bridge (rev 02) (prog-if 00 [Normal decode])
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 64
 	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
 	I/O behind bridge: 0000c000-0000cfff
 	Memory behind bridge: fe900000-fe9fffff
 	Prefetchable memory behind bridge: fff00000-000fffff
 	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
 00: 86 80 7b 25 07 01 a0 00 02 00 04 06 00 40 01 00
 10: 00 00 00 00 00 00 00 00 00 02 02 00 c0 c0 a0 02
 20: 90 fe 90 fe f0 ff 00 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
 
 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin A routed to IRQ 16
 	Region 4: I/O ports at eec0 [size=32]
 00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: c1 ee 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
 
 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin B routed to IRQ 19
 	Region 4: I/O ports at ef00 [size=32]
 00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: 01 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
 
 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin C routed to IRQ 18
 	Region 4: I/O ports at ef40 [size=32]
 00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: 41 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
 
 00:1d.3 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin A routed to IRQ 16
 	Region 4: I/O ports at ef80 [size=32]
 00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: 81 ef 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
 
 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin D routed to IRQ 23
 	Region 0: Memory at febfbc00 (32-bit, non-prefetchable) [size=1K]
 	Capabilities: [50] Power Management version 2
 		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 	Capabilities: [58] Debug port
 00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00
 10: 00 bc bf fe 00 00 00 00 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
 
 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode])
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
 	I/O behind bridge: 0000d000-0000dfff
 	Memory behind bridge: fea00000-feafffff
 	Prefetchable memory behind bridge: fff00000-000fffff
 	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
 	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
 00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00
 10: 00 00 00 00 00 00 00 00 00 03 03 40 d0 d0 80 02
 20: a0 fe a0 fe f0 ff 00 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
 
 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
 	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 
 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
 	Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin A routed to IRQ 18
 	Region 0: I/O ports at 01f0 [size=8]
 	Region 1: I/O ports at 03f4 [size=1]
 	Region 2: I/O ports at 0170 [size=8]
 	Region 3: I/O ports at 0374 [size=1]
 	Region 4: I/O ports at fc00 [size=16]
 	Region 5: Memory at 50000000 (32-bit, non-prefetchable) [size=1K]
 00: 86 80 db 24 07 00 88 02 02 8a 01 01 00 00 00 00
 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
 20: 01 fc 00 00 00 00 00 50 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
 
 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
 	Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
 	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Interrupt: pin B routed to IRQ 11
 	Region 4: I/O ports at 0400 [size=32]
 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80
 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
 
 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
 	Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0
 	Interrupt: pin B routed to IRQ 11
 	Region 0: I/O ports at e800 [size=256]
 	Region 1: I/O ports at ee80 [size=64]
 	Region 2: Memory at febffc00 (32-bit, non-prefetchable) [size=512]
 	Region 3: Memory at febff800 (32-bit, non-prefetchable) [size=256]
 	Capabilities: [50] Power Management version 2
 		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00
 10: 01 e8 00 00 81 ee 00 00 00 fc bf fe 00 f8 bf fe
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f3 80
 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 02 00 00
 
 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro] (prog-if 00 [VGA])
 	Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 64 (2000ns min), Cache Line Size: 16 bytes
 	Interrupt: pin A routed to IRQ 10
 	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
 	Region 1: I/O ports at b000 [size=256]
 	Region 2: Memory at fe8f0000 (32-bit, non-prefetchable) [size=64K]
 	Expansion ROM at fe8c0000 [disabled] [size=128K]
 	Capabilities: [58] AGP version 3.0
 		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
 		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
 	Capabilities: [50] Power Management version 2
 		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 00: 02 10 45 4e 87 01 b0 02 00 00 00 03 04 40 80 00
 10: 08 00 00 e8 01 b0 00 00 00 00 8f fe 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 02 00
 30: 00 00 8c fe 58 00 00 00 00 00 00 00 0a 01 08 00
 
 01:00.1 Display controller: ATI Technologies Inc Radeon R300 [Radeon 9500 Pro] (Secondary)
 	Subsystem: ATI Technologies Inc Radeon R300 NE [Radeon 9500 Pro]
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
 	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 64 (2000ns min), Cache Line Size: 16 bytes
 	Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
 	Region 1: Memory at fe8e0000 (32-bit, non-prefetchable) [size=64K]
 	Capabilities: [50] Power Management version 2
 		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 00: 02 10 65 4e 87 00 b0 02 00 00 80 03 04 40 00 00
 10: 08 00 00 e0 00 00 8e fe 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 03 00
 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 08 00
 
 02:01.0 Ethernet controller: Intel Corporation 82547EI Gigabit Ethernet Controller (LOM)
 	Subsystem: ASUSTeK Computer Inc. Unknown device 80f7
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
 	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 0 (63750ns min), Cache Line Size: 16 bytes
 	Interrupt: pin A routed to IRQ 18
 	Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
 	Region 2: I/O ports at cf80 [size=32]
 	Capabilities: [dc] Power Management version 2
 		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
 		Status: D0 PME-Enable- DSel=0 DScale=1 PME-
 00: 86 80 19 10 07 00 38 02 00 00 00 02 04 00 00 00
 10: 00 00 9e fe 00 00 00 00 81 cf 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f7 80
 30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 ff 00
 
 03:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
 	Subsystem: ASUSTeK Computer Inc. A8V Deluxe
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 64 (8000ns max), Cache Line Size: 16 bytes
 	Interrupt: pin A routed to IRQ 20
 	Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=2K]
 	Region 1: I/O ports at dc00 [size=128]
 	Capabilities: [50] Power Management version 2
 		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 00: 06 11 44 30 17 01 10 02 80 10 00 0c 04 40 00 00
 10: 00 f8 af fe 01 dc 00 00 00 00 00 00 00 00 00 00
 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 8a 80
 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 20
 
 03:04.0 RAID bus controller: Promise Technology, Inc. PDC20378 (FastTrak 378/SATA 378) (rev 02)
 	Subsystem: ASUSTeK Computer Inc. K8V Deluxe/PC-DL Deluxe motherboard
 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
 	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
 	Latency: 96 (1000ns min, 4500ns max), Cache Line Size: 576 bytes
 	Interrupt: pin A routed to IRQ 23
 	Region 0: I/O ports at df00 [size=64]
 	Region 1: I/O ports at dfa0 [size=16]
 	Region 2: I/O ports at d880 [size=128]
 	Region 3: Memory at feafe000 (32-bit, non-prefetchable) [size=4K]
 	Region 4: Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
 	Capabilities: [60] Power Management version 2
 		Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
 		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
 00: 5a 10 73 33 17 01 30 02 02 00 04 01 90 60 00 00
 10: 01 df 00 00 a1 df 00 00 81 d8 00 00 00 e0 af fe
 20: 00 00 ac fe 00 00 00 00 00 00 00 00 43 10 f5 80
 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 04 12
 
== setpci ==
 
 
== dmidecode ==
 
 # dmidecode 2.8
 SMBIOS 2.3 present.
 60 structures occupying 1920 bytes.
 Table at 0x000F04B0.
 
 Handle 0x0000, DMI type 0, 20 bytes
 BIOS Information
 	Vendor: American Megatrends Inc.
 	Version: 1023.001
 	Release Date: 06/20/2005
 	Address: 0xF0000
 	Runtime Size: 64 kB
 	ROM Size: 512 kB
 	Characteristics:
 		ISA is supported
 		PCI is supported
 		PNP is supported
 		APM is supported
 		BIOS is upgradeable
 		BIOS shadowing is allowed
 		ESCD support is available
 		Boot from CD is supported
 		Selectable boot is supported
 		BIOS ROM is socketed
 		EDD is supported
 		5.25"/1.2 MB floppy services are supported (int 13h)
 		3.5"/720 KB floppy services are supported (int 13h)
 		3.5"/2.88 MB floppy services are supported (int 13h)
 		Print screen service is supported (int 5h)
 		8042 keyboard services are supported (int 9h)
 		Serial services are supported (int 14h)
 		Printer services are supported (int 17h)
 		CGA/mono video services are supported (int 10h)
 		ACPI is supported
 		USB legacy is supported
 		AGP is supported
 		LS-120 boot is supported
 		ATAPI Zip drive boot is supported
 		BIOS boot specification is supported
 
 Handle 0x0001, DMI type 1, 25 bytes
 System Information
 	Manufacturer: To Be Filled By O.E.M.
 	Product Name: To Be Filled By O.E.M.
 	Version: To Be Filled By O.E.M.
 	Serial Number: To Be Filled By O.E.M.
 	UUID: 00020003-0004-0005-0006-000700080009
 	Wake-up Type: PCI PME#
 
 Handle 0x0002, DMI type 2, 8 bytes
 Base Board Information
 	Manufacturer: ASUSTeK Computer Inc.
 	Product Name: P4C800-E
 	Version: Rev 1.xx
 	Serial Number: MB-1234567890
 
 Handle 0x0003, DMI type 3, 17 bytes
 Chassis Information
 	Manufacturer: Chassis Manufacture
 	Type: Desktop
 	Lock: Not Present
 	Version: Chassis Version
 	Serial Number: Chassis Serial Number
 	Asset Tag: Asset-1234567890
 	Boot-up State: Safe
 	Power Supply State: Safe
 	Thermal State: Safe
 	Security Status: None
 	OEM Information: 0x00000001
 
 Handle 0x0004, DMI type 4, 35 bytes
 Processor Information
 	Socket Designation: CPU 1
 	Type: Central Processor
 	Family: Pentium 4
 	Manufacturer: Intel            
 	ID: 29 0F 00 00 FF FB EB BF
 	Signature: Type 0, Family 15, Model 2, Stepping 9
 	Flags:
 		FPU (Floating-point unit on-chip)
 		VME (Virtual mode extension)
 		DE (Debugging extension)
 		PSE (Page size extension)
 		TSC (Time stamp counter)
 		MSR (Model specific registers)
 		PAE (Physical address extension)
 		MCE (Machine check exception)
 		CX8 (CMPXCHG8 instruction supported)
 		APIC (On-chip APIC hardware supported)
 		SEP (Fast system call)
 		MTRR (Memory type range registers)
 		PGE (Page global enable)
 		MCA (Machine check architecture)
 		CMOV (Conditional move instruction supported)
 		PAT (Page attribute table)
 		PSE-36 (36-bit page size extension)
 		CLFSH (CLFLUSH instruction supported)
 		DS (Debug store)
 		ACPI (ACPI supported)
 		MMX (MMX technology supported)
 		FXSR (Fast floating-point save and restore)
 		SSE (Streaming SIMD extensions)
 		SSE2 (Streaming SIMD extensions 2)
 		SS (Self-snoop)
 		HTT (Hyper-threading technology)
 		TM (Thermal monitor supported)
 		PBE (Pending break enabled)
 	Version: Intel(R) Pentium(R) 4 CPU 2.80GHz                   
 	Voltage: 3.3 V 2.9 V
 	External Clock: 200 MHz
 	Max Speed: 3600 MHz
 	Current Speed: 2800 MHz
 	Status: Populated, Enabled
 	Upgrade: Socket 478
 	L1 Cache Handle: 0x0005
 	L2 Cache Handle: 0x0006
 	L3 Cache Handle: 0x0007
 	Serial Number: To Be Filled By O.E.M.
 	Asset Tag: To Be Filled By O.E.M.
 	Part Number: To Be Filled By O.E.M.
 
 Handle 0x0005, DMI type 7, 19 bytes
 Cache Information
 	Socket Designation: L1-Cache
 	Configuration: Enabled, Not Socketed, Level 1
 	Operational Mode: Varies With Memory Address
 	Location: Internal
 	Installed Size: 8 KB
 	Maximum Size: 8 KB
 	Supported SRAM Types:
 		Pipeline Burst
 	Installed SRAM Type: Pipeline Burst
 	Speed: Unknown
 	Error Correction Type: Single-bit ECC
 	System Type: Data
 	Associativity: 4-way Set-associative
 
 Handle 0x0006, DMI type 7, 19 bytes
 Cache Information
 	Socket Designation: L2-Cache
 	Configuration: Enabled, Not Socketed, Level 2
 	Operational Mode: Varies With Memory Address
 	Location: Internal
 	Installed Size: 512 KB
 	Maximum Size: 512 KB
 	Supported SRAM Types:
 		Pipeline Burst
 	Installed SRAM Type: Pipeline Burst
 	Speed: Unknown
 	Error Correction Type: Single-bit ECC
 	System Type: Unified
 	Associativity: 4-way Set-associative
 
 Handle 0x0007, DMI type 7, 19 bytes
 Cache Information
 	Socket Designation: L3-Cache
 	Configuration: Disabled, Not Socketed, Level 3
 	Operational Mode: Unknown
 	Location: Internal
 	Installed Size: 0 KB
 	Maximum Size: 0 KB
 	Supported SRAM Types:
 		Unknown
 	Installed SRAM Type: Unknown
 	Speed: Unknown
 	Error Correction Type: Unknown
 	System Type: Unknown
 	Associativity: Unknown
 
 Handle 0x0008, DMI type 5, 24 bytes
 Memory Controller Information
 	Error Detecting Method: None
 	Error Correcting Capabilities:
 		None
 	Supported Interleave: One-way Interleave
 	Current Interleave: One-way Interleave
 	Maximum Memory Module Size: 1024 MB
 	Maximum Total Memory Size: 4096 MB
 	Supported Speeds:
 		70 ns
 		60 ns
 		50 ns
 	Supported Memory Types:
 		SIMM
 		DIMM
 		SDRAM
 	Memory Module Voltage: 2.9 V
 	Associated Memory Slots: 4
 		0x0009
 		0x000A
 		0x000B
 		0x000C
 	Enabled Error Correcting Capabilities:
 		None
 
 Handle 0x0009, DMI type 6, 12 bytes
 Memory Module Information
 	Socket Designation: DIMM A1
 	Bank Connections: 1 0
 	Current Speed: Unknown
 	Type: DIMM SDRAM
 	Installed Size: 512 MB (Double-bank Connection)
 	Enabled Size: 512 MB (Double-bank Connection)
 	Error Status: OK
 
 Handle 0x000A, DMI type 6, 12 bytes
 Memory Module Information
 	Socket Designation: DIMM A2
 	Bank Connections: 3 2
 	Current Speed: Unknown
 	Type: Unknown
 	Installed Size: Not Installed
 	Enabled Size: Not Installed
 	Error Status: OK
 
 Handle 0x000B, DMI type 6, 12 bytes
 Memory Module Information
 	Socket Designation: DIMM B1
 	Bank Connections: 5 4
 	Current Speed: Unknown
 	Type: DIMM SDRAM
 	Installed Size: 512 MB (Double-bank Connection)
 	Enabled Size: 512 MB (Double-bank Connection)
 	Error Status: OK
 
 Handle 0x000C, DMI type 6, 12 bytes
 Memory Module Information
 	Socket Designation: DIMM B2
 	Bank Connections: 7 6
 	Current Speed: Unknown
 	Type: Unknown
 	Installed Size: Not Installed
 	Enabled Size: Not Installed
 	Error Status: OK
 
 Handle 0x000D, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: PS2Mouse
 	External Connector Type: PS/2
 	Port Type: Mouse Port
 
 Handle 0x000E, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: Keyboard
 	External Connector Type: PS/2
 	Port Type: Keyboard Port
 
 Handle 0x000F, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB1
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0010, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB2
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0011, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB3
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0012, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB4
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0013, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB5
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0014, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB6
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0015, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB7
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0016, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: USB8
 	External Connector Type: Access Bus (USB)
 	Port Type: USB
 
 Handle 0x0017, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: LPT 1
 	External Connector Type: DB-25 male
 	Port Type: Parallel Port ECP/EPP
 
 Handle 0x0018, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: COM 1
 	External Connector Type: DB-9 male
 	Port Type: Serial Port 16550A Compatible
 
 Handle 0x0019, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: COM 2
 	External Connector Type: DB-9 male
 	Port Type: Serial Port 16550A Compatible
 
 Handle 0x001A, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: Audio Mic In
 	External Connector Type: Mini Jack (headphones)
 	Port Type: Audio Port
 
 Handle 0x001B, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: Audio Line In
 	External Connector Type: Mini Jack (headphones)
 	Port Type: Audio Port
 
 Handle 0x001C, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: Audio Line Out
 	External Connector Type: Mini Jack (headphones)
 	Port Type: Audio Port
 
 Handle 0x001D, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: Not Specified
 	Internal Connector Type: None
 	External Reference Designator: LAN
 	External Connector Type: RJ-45
 	Port Type: Network Port
 
 Handle 0x001E, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: AUX
 	Internal Connector Type: On Board Sound Input From CD-ROM
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Audio Port
 
 Handle 0x001F, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: CD
 	Internal Connector Type: On Board Sound Input From CD-ROM
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Audio Port
 
 Handle 0x0020, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: PRI_IDE
 	Internal Connector Type: On Board IDE
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0021, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: SEC_IDE
 	Internal Connector Type: On Board IDE
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0022, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: FLOPPY
 	Internal Connector Type: On Board Floppy
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0023, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: CHA_FAN
 	Internal Connector Type: Other
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0024, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: CPU_FAN
 	Internal Connector Type: Other
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0025, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: PWR_FAN
 	Internal Connector Type: Other
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0026, DMI type 8, 9 bytes
 Port Connector Information
 	Internal Reference Designator: ATXPWR
 	Internal Connector Type: Other
 	External Reference Designator: Not Specified
 	External Connector Type: None
 	Port Type: Other
 
 Handle 0x0027, DMI type 9, 13 bytes
 System Slot Information
 	Designation: AGP
 	Type: 32-bit AGP 8x
 	Current Usage: In Use
 	Length: Short
 	Characteristics:
 		3.3 V is provided
 
 Handle 0x0028, DMI type 9, 13 bytes
 System Slot Information
 	Designation: PCI1
 	Type: 32-bit PCI
 	Current Usage: Available
 	Length: Short
 	ID: 1
 	Characteristics:
 		5.0 V is provided
 		3.3 V is provided
 		PME signal is supported
 
 Handle 0x0029, DMI type 9, 13 bytes
 System Slot Information
 	Designation: PCI2
 	Type: 32-bit PCI
 	Current Usage: Available
 	Length: Short
 	ID: 2
 	Characteristics:
 		5.0 V is provided
 		3.3 V is provided
 		PME signal is supported
 
 Handle 0x002A, DMI type 9, 13 bytes
 System Slot Information
 	Designation: PCI3
 	Type: 32-bit PCI
 	Current Usage: Available
 	Length: Short
 	ID: 3
 	Characteristics:
 		5.0 V is provided
 		3.3 V is provided
 		PME signal is supported
 
 Handle 0x002B, DMI type 9, 13 bytes
 System Slot Information
 	Designation: PCI4
 	Type: 32-bit PCI
 	Current Usage: Available
 	Length: Short
 	ID: 4
 	Characteristics:
 		5.0 V is provided
 		3.3 V is provided
 		PME signal is supported
 
 Handle 0x002C, DMI type 9, 13 bytes
 System Slot Information
 	Designation: PCI5
 	Type: 32-bit PCI
 	Current Usage: Available
 	Length: Short
 	ID: 5
 	Characteristics:
 		5.0 V is provided
 		3.3 V is provided
 		PME signal is supported
 
 Handle 0x002D, DMI type 10, 6 bytes
 On Board Device Information
 	Type: Ethernet
 	Status: Enabled
 	Description:  Intel CSA 82547EI
 
 Handle 0x002E, DMI type 11, 5 bytes
 OEM Strings
 	String 1: To Be Filled By O.E.M.
 	String 2: To Be Filled By O.E.M.
 	String 3: To Be Filled By O.E.M.
 	String 4: To Be Filled By O.E.M.
 
 Handle 0x002F, DMI type 13, 22 bytes
 BIOS Language Information
 	Installable Languages: 1
 		en|US|iso8859-1
 	Currently Installed Language: en|US|iso8859-1
 
 Handle 0x0030, DMI type 16, 15 bytes
 Physical Memory Array
 	Location: System Board Or Motherboard
 	Use: System Memory
 	Error Correction Type: Single-bit ECC
 	Maximum Capacity: 4 GB
 	Error Information Handle: Not Provided
 	Number Of Devices: 4
 
 Handle 0x0031, DMI type 19, 15 bytes
 Memory Array Mapped Address
 	Starting Address: 0x00000000000
 	Ending Address: 0x100000003FF
 	Range Size: 1073741825 kB
 	Physical Array Handle: 0x0030
 	Partition Width: 0
 
 Handle 0x0032, DMI type 17, 27 bytes
 Memory Device
 	Array Handle: 0x0030
 	Error Information Handle: Not Provided
 	Total Width: 64 bits
 	Data Width: 64 bits
 	Size: 512 MB
 	Form Factor: DIMM
 	Set: None
 	Locator: DIMM0
 	Bank Locator: BANK0
 	Type: DDR
 	Type Detail: Synchronous
 	Speed: Unknown
 	Manufacturer: Manufacturer0
 	Serial Number: SerNum0
 	Asset Tag: AssetTagNum0
 	Part Number: PartNum0
 
 Handle 0x0033, DMI type 20, 19 bytes
 Memory Device Mapped Address
 	Starting Address: 0x00000000000
 	Ending Address: 0x0001FFFFFFF
 	Range Size: 512 MB
 	Physical Device Handle: 0x0032
 	Memory Array Mapped Address Handle: 0x0031
 	Partition Row Position: 1
 
 Handle 0x0034, DMI type 17, 27 bytes
 Memory Device
 	Array Handle: 0x0030
 	Error Information Handle: Not Provided
 	Total Width: Unknown
 	Data Width: Unknown
 	Size: No Module Installed
 	Form Factor: DIMM
 	Set: None
 	Locator: DIMM1
 	Bank Locator: BANK1
 	Type: Unknown
 	Type Detail: Unknown
 	Speed: Unknown
 	Manufacturer: Manufacturer1
 	Serial Number: SerNum1
 	Asset Tag: AssetTagNum1
 	Part Number: PartNum1
 
 Handle 0x0035, DMI type 20, 19 bytes
 Memory Device Mapped Address
 	Starting Address: 0x00000000000
 	Ending Address: 0x000000003FF
 	Range Size: 1 kB
 	Physical Device Handle: 0x0034
 	Memory Array Mapped Address Handle: 0x0031
 	Partition Row Position: 1
 
 Handle 0x0036, DMI type 17, 27 bytes
 Memory Device
 	Array Handle: 0x0030
 	Error Information Handle: Not Provided
 	Total Width: 64 bits
 	Data Width: 64 bits
 	Size: 512 MB
 	Form Factor: DIMM
 	Set: None
 	Locator: DIMM2
 	Bank Locator: BANK2
 	Type: DDR
 	Type Detail: Synchronous
 	Speed: Unknown
 	Manufacturer: Manufacturer2
 	Serial Number: SerNum2
 	Asset Tag: AssetTagNum2
 	Part Number: PartNum2
 
 Handle 0x0037, DMI type 20, 19 bytes
 Memory Device Mapped Address
 	Starting Address: 0x00020000000
 	Ending Address: 0x0003FFFFFFF
 	Range Size: 512 MB
 	Physical Device Handle: 0x0036
 	Memory Array Mapped Address Handle: 0x0031
 	Partition Row Position: 1
 
 Handle 0x0038, DMI type 17, 27 bytes
 Memory Device
 	Array Handle: 0x0030
 	Error Information Handle: Not Provided
 	Total Width: Unknown
 	Data Width: Unknown
 	Size: No Module Installed
 	Form Factor: DIMM
 	Set: None
 	Locator: DIMM3
 	Bank Locator: BANK3
 	Type: Unknown
 	Type Detail: Unknown
 	Speed: Unknown
 	Manufacturer: Manufacturer3
 	Serial Number: SerNum3
 	Asset Tag: AssetTagNum3
 	Part Number: PartNum3
 
 Handle 0x0039, DMI type 20, 19 bytes
 Memory Device Mapped Address
 	Starting Address: 0x00000000000
 	Ending Address: 0x000000003FF
 	Range Size: 1 kB
 	Physical Device Handle: 0x0038
 	Memory Array Mapped Address Handle: 0x0031
 	Partition Row Position: 1
 
 Handle 0x003A, DMI type 32, 20 bytes
 System Boot Information
 	Status: No errors detected
 
 Handle 0x003B, DMI type 127, 4 bytes
 End Of Table