View source for Board:a-trend/atc-6220

This page describes how to use coreboot on the '''[http://www.motherboard.cz/mb/atrend/atc6220.htm ATC-6220]''' mainboard. It is maintained by [[User:Uwe|Uwe Hermann]].

== Status ==

{{Status|

|CPU_status = OK
|CPU_L1_status = OK
|CPU_L1_comments = CPU: L1 I cache: 16K, L1 D cache: 16K
|CPU_L2_status = OK
|CPU_L2_comments = CPU: L2 cache: 256K
|CPU_L3_status = N/A
|CPU_multiple_status = N/A
|CPU_multicore_status = N/A
|CPU_virt_status = N/A

|RAM_EDO_status = N/A
|RAM_SDRAM_status = OK
|RAM_SODIMM_status = N/A
|RAM_DDR_status = N/A
|RAM_DDR2_status = N/A
|RAM_DDR3_status = N/A
|RAM_dualchannel_status = N/A
|RAM_ecc_status = WIP
|RAM_ecc_comments = Not yet supported by the coreboot 440BX code, but it's on our TODO list.

|IDE_status = OK
|IDE_25_status = N/A
|SATA_status = N/A
|USB_status = Untested
|USB_comments = 
|Onboard_VGA_status = N/A
|Onboard_ethernet_status = N/A
|Onboard_audio_status = N/A
|Onboard_modem_status = N/A
|Onboard_firewire_status = N/A
|Smartcard_status = N/A
|Onboard_CF_status = N/A
|Onboard_PCMCIA_status = N/A
|Onboard_SCSI_status = N/A

|ISA_cards_status = Untested
|AMR_cards_status = N/A
|Mini_PCI_cards_status = N/A
|PCIX_cards_status = N/A
|PCI_cards_status = OK
|PCI_cards_comments = All 4 PCI slots tested using a PCI graphics card.
|AGP_cards_status = OK
|AGP_cards_comments = Tested: AGP graphics card.
|PCIE_cards_status = N/A
|PCIE_x1_status = N/A
|PCIE_x2_status = N/A
|PCIE_x4_status = N/A
|PCIE_x8_status = N/A
|PCIE_x16_status = N/A
|PCIE_x32_status = N/A
|HTX_status = N/A

|Floppy_status = Untested
|COM1_status = OK
|COM1_comments = Works, but there's a small Baud rate fix needed in coreboot. For now, it works using using 230400 (instead of 115200) as Baud rate.
|COM2_status = Untested
|PP_status = OK
|PP_comments = Doing '''modprobe ppdev''' works, but no further tests were performed.
|PS2_keyboard_status = OK
|PS2_mouse_status = Untested
|Game_port_status = N/A
|IR_status = 
|Speaker_status = OK
|DiskOnChip_status = N/A

|Sensors_status = OK
|Sensors_comments = Works fine, you can use the '''w83781d''', '''i2c-piix4''', and '''eeprom''' kernel modules.
|Watchdog_status = N/A
|CAN_bus_status = N/A
|CPUfreq_status = Untested
|Powersave_status = N/A
|ACPI_status = No
|ACPI_comments = There's no ACPI implementation for this board.
|SMBus_status = N/A
|Reboot_status = OK
|Poweroff_status = No
|Poweroff_comments = Running '''halt''' doesn't properly power-down the board.
|LEDs_status = N/A
|HPET_status = N/A
|RNG_status = N/A
|WakeOnModem_status = 
|WakeOnLAN_status = 
|WakeOnKeyboard_status = 
|WakeOnMouse_status = 
|Flashrom_status = OK

}}


{{PD-self}}