Board:bcom/winnetp680: Difference between revisions

From coreboot
Jump to navigation Jump to search
m (Phcoder moved page BCOM WinNET P680 to Board:bcom/winnetp680)
 
(12 intermediate revisions by 3 users not shown)
Line 1: Line 1:
This page describes how to use coreboot on the BCOM WinNET P680 motherboard.  This board is used on the HP/Neoware e140 thin client.
This page describes how to use coreboot on the BCOM WinNET P680 motherboard.  This board is used in the HP/Neoware e140 (aka CA22) and Igel 4210LX Winestra thin clients.


This page is a work in progress.
This page is a work in progress.
Line 5: Line 5:
== Status ==
== Status ==


This board works with target/bcom/winnetp680, except that it needs rev 3566 of src/southbridge/via/vt8237r.
Works somewhat. See known problems below. Work is in progress to fix these issues.


==Known problems==
==Known problems==
* L1/L2 cache are running extremely slow, 11-12MB/s per Memtest86+. As a result, loading kernel/initrd is very slow
* irq_tables.c from the factory BIOS does not work.  The epia-cn table has been substituted, but it has problems too (Ethernet doesn't work right: 50% packet loss.).  A workaround is to use the kernel parameter "irqpoll"
* Boot log shows INT15 handler isn't working
* hda in Linux is hde in FILO
* hda in Linux is hde in FILO
* loading kernel/initrd is very slow
* irq_tables.c from the factory BIOS does not work.  The epia-cn table has been substituted, but it has problems too (Ethernet doesn't work right: 50% packet loss.).  A workaround is to use the kernel parameter "irqpoll"
* Current code is broken (doesn't compile).  Pull rev 3566 of src/southbridge/via/vt8237r


{{Status|
{{Status|
Line 31: Line 32:
|RAM_DDR_status = N/A
|RAM_DDR_status = N/A
|RAM_DDR2_status = OK
|RAM_DDR2_status = OK
|RAM_DDR2_comments = Board only has a single laptop-sized DDR2 slot which does not support many larger (1GB+) sticks in the factory BIOS. Some of this may be corrected by coreboot, but some is a chipset limitation. More should be known when coreboot is working again.
|RAM_DDR3_status = N/A
|RAM_DDR3_status = N/A
|RAM_dualchannel_status = N/A
|RAM_dualchannel_status = N/A
|RAM_ecc_status = Untested
|RAM_ecc_status = Untested


|IDE_status = OK
|IDE_status = Partial
|IDE_comments = hda in Linux is hde in FILO
|IDE_comments = hda in Linux is hde in FILO.  IDE device doesn't get reset properly on boot (sometimes shows up as a floating bus)
|IDE_CF_status = N/A
|IDE_CF_status = N/A
|IDE_25_status = N/A
|IDE_25_status = N/A
|CDROM_DVD_status = N/A
|CDROM_DVD_status = N/A
|SATA_status = N/A
|SATA_status = N/A
|SCSI_status = N/A
|USB_status = OK
|USB_status = OK
|Onboard_VGA_status = OK
|Onboard_VGA_status = OK
Line 50: Line 53:
|Onboard_firewire_status = N/A
|Onboard_firewire_status = N/A
|Smartcard_status = N/A
|Smartcard_status = N/A
|Onboard_CF_status = N/A
|Onboard_CF_status = Unknown
|Onboard_CF_comments = Igel 4210LX has CF slot with jumpers to select Master/Slave on the same "chain" as the 44-pin IDE connector. Untested but should work. It should also be possible to solder a CF slot onto the Neoware board.
|Onboard_PCMCIA_status = N/A
|Onboard_PCMCIA_status = N/A


Line 57: Line 61:
|AGP_cards_status = N/A
|AGP_cards_status = N/A
|PCI_cards_status = Untested
|PCI_cards_status = Untested
|PCI_cards_comments =  
|PCI_cards_comments = Needs rightward angle adapter to fit card into case
|Mini_PCI_cards_status = N/A
|PCIX_cards_status = N/A
|PCIE_x1_status = N/A
|PCIE_x1_status = N/A
|PCIE_x2_status = N/A
|PCIE_x2_status = N/A
Line 68: Line 74:
|Floppy_status = N/A
|Floppy_status = N/A
|COM1_status = OK
|COM1_status = OK
|COM2_status = N/A
|COM2_status = OK
|PP_status = Untested
|PP_status = Untested
|PP_comments =
|PS2_keyboard_status = OK
|PS2_keyboard_status = OK
|PS2_mouse_status = OK
|PS2_mouse_status = OK
|Game_port_status = N/A
|Game_port_status = N/A
|IR_status = N/A
|IR_status = N/A
|Speaker_status = Fail
|Speaker_status = OK
|Speaker_comments =
|DiskOnChip_status = N/A
|DiskOnChip_status = N/A


|Sensors_status = Untested
|Sensors_status = OK
|Sensors_comments =
|Watchdog_status = N/A
|Watchdog_status = N/A
|Watchdog_comments =
|CAN_bus_status = N/A
|CAN_bus_status = N/A
|CPUfreq_status = ?
|CPUfreq_status = Unknown
|CPUfreq_comments =
|Powersave_status = N/A
|Powersave_status = N/A
|ACPI_status = Fail
|ACPI_status = Fail
Line 102: Line 103:
|WakeOnMouse_status = Untested
|WakeOnMouse_status = Untested
|Flashrom_status = OK
|Flashrom_status = OK
|Flashrom_comments = Patch needed, Peter Stuge and Alex Mauer have it.
|Flashrom_comments = R1733 or higher


}}
}}

Latest revision as of 23:21, 18 January 2014

This page describes how to use coreboot on the BCOM WinNET P680 motherboard. This board is used in the HP/Neoware e140 (aka CA22) and Igel 4210LX Winestra thin clients.

This page is a work in progress.

Status

Works somewhat. See known problems below. Work is in progress to fix these issues.

Known problems

  • L1/L2 cache are running extremely slow, 11-12MB/s per Memtest86+. As a result, loading kernel/initrd is very slow
  • irq_tables.c from the factory BIOS does not work. The epia-cn table has been substituted, but it has problems too (Ethernet doesn't work right: 50% packet loss.). A workaround is to use the kernel parameter "irqpoll"
  • Boot log shows INT15 handler isn't working
  • hda in Linux is hde in FILO
Device/functionality Status Comments
CPU
CPU works OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
L1 cache enabled OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK Always on
L2 cache enabled OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK Always on
L3 cache enabled OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Multiple CPU support OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Multi-core support OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Hardware virtualization OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
RAM
EDO OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
SDRAM OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
SO-DIMM OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
DDR OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
DDR2 OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK Board only has a single laptop-sized DDR2 slot which does not support many larger (1GB+) sticks in the factory BIOS. Some of this may be corrected by coreboot, but some is a chipset limitation. More should be known when coreboot is working again.
DDR3 OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Dual channel support OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
ECC support OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
On-board Hardware
On-board IDE 3.5" OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Partial hda in Linux is hde in FILO. IDE device doesn't get reset properly on boot (sometimes shows up as a floating bus)
On-board IDE 2.5" OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board SATA OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board SCSI OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
On-board USB OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
On-board VGA OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK Needs factory VGA bios and bochsbios.
On-board Ethernet OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Partial 50% packet loss. Probably due to a bad IRQ table. See above.
On-board Audio OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
On-board Modem OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board FireWire OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board Smartcard reader OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board CompactFlash OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown Igel 4210LX has CF slot with jumpers to select Master/Slave on the same "chain" as the 44-pin IDE connector. Untested but should work. It should also be possible to solder a CF slot onto the Neoware board.
On-board PCMCIA OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board Wifi OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board Bluetooth OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board SD card reader OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Add-on slots/cards
ISA add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Audio/Modem-Riser (AMR/CNR) cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested Needs rightward angle adapter to fit card into case
Mini-PCI add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Mini-PCI-Express add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
PCI-X add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
AGP graphics cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x1 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x2 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x4 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x8 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x16 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x32 add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
HTX add-on cards OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Legacy / Super I/O
Floppy OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Serial port 1 (COM1) OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Serial port 2 (COM2) OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Parallel port OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
PS/2 keyboard OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
PS/2 mouse OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Game port OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Infrared OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PC speaker OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
DiskOnChip OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Input
Trackpoint OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Touchpad OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Fn Hotkeys OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Fingerprint Reader OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Laptop
Docking VGA OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking LAN OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking USB OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking Audio OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking Displayport OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Thinklight OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Webcam OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Miscellaneous
Sensors / fan control OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Hardware watchdog OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
SMBus OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
CAN bus OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
CPU frequency scaling OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Other powersaving features OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
ACPI OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Fail
Reboot OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Fail system resets, but on reboot, FILO can't see the IDE device.
Poweroff OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Fail
Suspend OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Nonstandard LEDs OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
High precision event timers (HPET) OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
Random number generator (RNG) OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Wake on modem ring OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
Wake on LAN OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
Wake on keyboard OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
Wake on mouse OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
TPM OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Flashrom OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK R1733 or higher


Public domain I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide.

In case this is not legally possible:
I grant anyone the right to use this work for any purpose, without any conditions, unless such conditions are required by law.