Board:lenovo/t530: Difference between revisions

Revision as of 17:47, 13 September 2014

Specification

The machine has:

- Chipset: Intel QM77
- GPU's: Intel Integrated HD Graphics
       : Discrete NVIDIA NVS 5400M (1 GB VRAM) with Optimus Technology

and pci configuration of:

-[0000:00]-+-00.0  8086:0154
           +-02.0  8086:0166
           +-16.0  8086:1e3a
           +-19.0  8086:1502
           +-1a.0  8086:1e2d
           +-1b.0  8086:1e20
           +-1c.0-[02]----00.0  1180:e823
           +-1c.1-[03]----00.0  8086:4238
           +-1c.2-[04-0b]--
           +-1d.0  8086:1e26
           +-1f.0  8086:1e55
           +-1f.2  8086:1e03
           \-1f.3  8086:1e22

Status

Thanks for your interest in Lenovo T530 port. Issues:

EHCI output failure after sysagent
no S3
no MRC cache
MRC needs watchdog
yellow USB port isn't powered in power-off state.

(Tested on X230 *not tested* on the T530):

RAM module combinations of 8G+8G
USB (both 2.0 and 3.0 ports)
Video (both internal and VGA)
Expresscard slot (including hotplugging)
Sound (integrated speakers, integrated mic, external headphones, external mic)
LAN
mini-PCIe slots (both wlan and wwan)
Linux (through GRUB-as-payload)
Windows (through GRUB-as-payload loading SeaBIOS image from disk; you have to use extracted VGA blob, dumped from memory isn't good enough)
SD card slot
Thermal management
Fingerprint reader.
Webcam
Keyboard backlight
Thinklight.
bluetooth
dock
msata (fixed in commit c8f54a1109072706e2fa091dc9ab4ad3eb057b42)

Not tested:

mini displayport (probably works)

Proprietary components status

CPU Microcode (optional)
ME(Management Engine) => you do not have to touch it (just leave it where it is)
EC(Embedded Controller) => you do not have to touch it (just leave it where it is)

!!! WARNING !!!

The ME is pretty much completely evil in both every imaginable and unimaginable way! This Coreboot port really only serves the purpose of two things:

1.) Increasing the attack surface of the ME controller.

2.) Replacing UEFI junk.

There is very little "freedom" gained from Coreboot as the ME controller is /so/ utterly pervasive! Do your research!

GPIO layout

This information should not be considered reliable in any way, shape or form

GPIO57 - OUT - controls..

General Purpose Events layout

GPE? - EC SCI
GPE? - EC SMI

Flashing

T530 has 2 flash chips of 8M and 4M. They're concatenated to one virtual flash chip of 12M which is itself subdivided in roughly in 4 parts:

Descriptor (12K)
ME firmware (5M-12K)
System flash (7M)

ME firmware is not readable. Vendor firmware locks the flash and so you need to flash externally (unless until someone figures out a way around it).

Proceeds as follows:

Turn off your laptop, remove battery and AC adapter.
Remove the keyboard.
Connect your external SPI flasher to the top SPI chip which is under palm resting space, on left side of the board. It's a 4M chip. IF you've chosen CBFS_SIZE 4M or smaller that's the only chip you need to reflash.

I recommend using SOIC clip. Depending on the flasher you use, you may have to use separate 3.3V source. Make sure not to feed more than 3.3V ot the chip. I used buspirate as flasher and 3.3V power lines from another computer.

Read the flash. Twice. Compare the files to be sure. Save a copy of it on

external media.

flashrom -p <yourprogrammer> -r flash.bin
flashrom -p <yourprogrammer> -r flash2.bin
diff flash.bin flash2.bin

If they don't match, do not proceed. If the file is 8M, you're flashing wrong chip, connect to the right one.

Write the flash. Since you have to write only top 4M, first split out those 4M:

 dd of=top.rom bs=1M if=build/coreboot.rom skip=8

Use flashrom to flash top.rom.

If you have trouble reading the chip successfully, the most common problems are

insufficient power supply
bad contacts
too long wires
bad pinout

The cable shipped with buspirate was too long, and needed to be trimmed.