Shuttle SN25P

Status

This is just a work-in-progress status page, the port is not functional yet.

Linux kernel hangs in tty_io.c console_init() and VGA is not working...

Tried various kernels:

• from 2.6.23 to 2.6.27-rc8-git
• 32 & 64 bit versions
• gcc-4.1.2 & gcc-4.3.1
• different configs (debug, etc...)
• -0s vs -O2

The hang is apparently a kernel panic (blinking leds at ~10s interval) but there's no message on the serial console about it. still locking up on spin_lock_irqsave()

If I start coreboot from poweroff, it hangs in running the vga bios under emulation

I've ran out of ideas, stuck...

Background

I started my work on Shuttle SN25P motherboard by looking at supported mainboards page, chose a supported one that has similar hardware (Asus A8N-E)

Uwe told me where to start modifiying the code to adapt it to motherboard specificities, and more importantly, where to find the information to put in place.

Hardware

• AMD K8 Northbridge
• NVIDIA CK804 Southbridge
• ITE IT8712F Super I/O
• AMD Opteron 165 dual core Socket 939
• 2 * 1 GB PC-3200 DDR-SDRAM
• RD1 PMC4 BIOS Savior on PLCC socket
• PMC Pm49FL004T-33JC - spare flash chips for work and backup (in case I flash the RD1 with a non working image)
• SST 49LF004B 33-4C-NH - spare, not tested

OK

• flashrom from linux over legacy BIOS
• Serial console
• Coreboot runs
• Load & run payload (tested OK: EtherBoot, coreinfo, filo & memtest86)
• PS2 Keyboard - works in filo, but status leds don't (may need irq working properly ???)
• Filo loads a kernel & jump to its entry point

NOK

• Kernel start to boot and hang at the console handling code, right after "Detected 1800.234 MHz processor.", trying to acquire_console_sem()

• VGA (not in coreboot, not in filo, not in memtest86, not in linux kernel)
• Etherboot (onboard nvidia ethernet adapter not properly configured by coreboot)
• Network

Files

• Config.lb - should be OK
• irq_tables.c - should be OK
• mptable.c - should be OK, linux kernel apic=debug output is identical as with legacy BIOS
• get_bus_conf.c - should be OK (be careful to look for PCI busses enumeration order differences between coreboot and legacy BIOS. Don't blindly try to replicate what lspci over BIOS is telling you, look at what coreboot debug info is showing for PCI busses enumeration)

Information gathering

All output from these tools are on Shuttle_SN25P_Infos

• /proc/interrupts
• dmidecode - Flash ROM chip size
• getpir - infos for irq_tables.c & mptable.c
• mptable - infos for mptable.c
• superiotool -dV - infos for Config.lb device tree
• flashrom -V - Is your motherboard flashrom capable (northbridge + super I/O + flash chip)
• lspci -tnvv - PCI bus tree from legacy BIOS
• lspci -vvvxx - PCI devices informations
• setpci -s 0:0:1.0 7c.L - infos for "Initialize interrupt mapping" in mptable.c
• setpci -s 0:0:1.0 80.L - infos for "Initialize interrupt mapping" in mptable.c
• setpci -s 0:0:1.0 84.L - infos for "Initialize interrupt mapping" in mptable.c

TODO

• Make it boot to Xorg
• Test onboard HW: SATA, CDROM, USB, Firewire, mouse, keyboard, audio, fan & temperature control
• PCIe-x16 GFX & ethernet
• HPET
• ACPI
• Etherboot for BCM - TG3 PCIe 1x addon card
• LAB ? (may need bigger flash)
• Other payloads

Notes

• Linux kernel command line options:
  • Used ones:
    • apic=debug
    • acpi=off
    • debug
    • irqpoll
    • hpet=force
    • maxcpus=1
    • mem=64M
    • loglevel=8
    • console=tty0
    • console=ttyS0,115200
    • earlycon=uart8250,io,0x3f8
    • earlyprintk=serial,ttyS0,115200
  • To test:
    • noapic
    • parport=0
    • lapic
    • disable_8254_timer
    • enable_8254_timer

• PCI bus numbering is dynamic:
  • do not try to hardcode the numbers
  • get_bus_conf() creates a bus number map for use in mptable.c & irq_tables.c
  • isa_bus is just assigned a number after the last pci-style bus