Board:lenovo/x201

Status

Issues:

• suspend to RAM (S3) currently fails.
• No expresscard hotplug
• Sometimes Gnome starts to think that battery is 10 time larger than real

 Information from sysfs remains correct.

• On my X201 there due to recent hardware failure thermal management doesn't

 work with either coreboot or original BIOS. Before this hardware fault
 happened thermal management worked under coreboot as well.

Tested:

• RAM module combinations of 4G+4G, 4G, 2G+2G,4G+2G, 2G
• USB
• Video (both internal and VGA)
• Expresscard slot
• Sound
• LAN
• mini-PCIe slots (both wlan and wwan)
• Linux (through GRUB-as-payload)
• Windows (through GRUB-as-payload loading SeaBIOS image from disk)
• SD card slot
• Thermal management

Not tested:

• Modem

proprietary components status

• CPU Microcode (optional)
• VGA option rom (optional): you need it if you wantgraphics in SeaBIOS but most payloads should work without it (text mode)
• ME(Management Engine) => you do not have to touch it(just leave it where it is)
• EC(Embedded Controller) => you do not have to touch it(just leave it where it is)

Code

• The code is here

Flashing

• you need an external programmer to flash it.
• The flash chip is divided between the ME and the BIOS:

<phcoder> First 5M is ME firmware, last 3M is BIOS/coreboot

• To find exactly where it's divided run that command(the example below is on another laptop):

[root@N71Jq ~]# flashrom -r bios.bin -pinternal:laptop=force_I_want_a_brick
flashrom v0.9.6.1-r1564 on Linux 3.8.2-1-LIBRE (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OK.
========================================================================
WARNING! You may be running flashrom on an unsupported laptop. We could
not detect this for sure because your vendor has not setup the SMBIOS
tables correctly. You can enforce execution by adding
'-p internal:laptop=this_is_not_a_laptop' to the command line, but
please read the following warning if you are not sure.

Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See http://www.flashrom.org/Laptops for details.

If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
Found chipset "Intel HM55". 
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
FREG2: WARNING: Management Engine region (0x00003000-0x001fffff) is locked.
Please send a verbose log to flashrom@flashrom.org if this board is not listed on
http://flashrom.org/Supported_hardware#Supported_mainboards yet.
Writes have been disabled. You can enforce write support with the
ich_spi_force programmer option, but it will most likely harm your hardware!
If you force flashrom you will get no support if something breaks.
OK.
Found SST flash chip "SST25VF032B" (4096 kB, SPI) at physical address 0xffc00000.
Reading flash... Transaction error!
Read operation failed!
FAILED.

it will print the ME regions:

FREG2: WARNING: Management Engine region (0x00003000-0x001fffff) is locked.

it will also print the chip:

Found SST flash chip "SST25VF032B" (4096 kB, SPI) at physical address 0xffc00000.

=> verify if its voltage match with the programmer voltage...

• Then man flashrom says:

       -l, --layout <file>
              Read ROM layout from <file>.

              flashrom  supports  ROM  layouts. This allows you to flash certain parts of the flash chip only. A ROM layout file contains multiple lines with the following
              syntax:

                startaddr:endaddr imagename

              startaddr and endaddr are hexadecimal addresses within the ROM file and do not refer to any physical address. Please note that using a 0x  prefix  for  those
              hexadecimal  numbers  is  not necessary, but you can't specify decimal/octal numbers.  imagename is an arbitrary name for the region/image from  startaddr to
              endaddr (both addresses included).

              Example:

                00000000:00008fff gfxrom
                00009000:0003ffff normal
                00040000:0007ffff fallback

              If you only want to update the image named normal in a ROM based on the layout above, run

                flashrom -p prog --layout rom.layout --image normal -w some.rom

              To update only the images named normal and fallback, run:

                flashrom -p prog -l rom.layout -i normal -i fallback -w some.rom

              Overlapping sections are not supported.