Board:lenovo/t530

Specification

The machine has:

- Chipset: Intel QM77
- GPU's: Intel Integrated HD Graphics
       : Discrete NVIDIA NVS 5400M (1 GB VRAM) with Optimus Technology

and pci configuration of:

-[0000:00]-+-00.0  8086:0154
           +-02.0  8086:0166
           +-16.0  8086:1e3a
           +-19.0  8086:1502
           +-1a.0  8086:1e2d
           +-1b.0  8086:1e20
           +-1c.0-[02]----00.0  1180:e823
           +-1c.1-[03]----00.0  8086:4238
           +-1c.2-[04-0b]--
           +-1d.0  8086:1e26
           +-1f.0  8086:1e55
           +-1f.2  8086:1e03
           \-1f.3  8086:1e22

Status

Thanks for your interest in Lenovo T530 port. Issues:

• EHCI output failure after sysagent
• no S3
• no MRC cache
• MRC needs watchdog
• yellow USB port isn't powered in power-off state.

(Tested on X230 *not tested* on the T530):

• RAM module combinations of 8G+8G
• USB (both 2.0 and 3.0 ports)
• Video (both internal and VGA)
• Expresscard slot (including hotplugging)
• Sound (integrated speakers, integrated mic, external headphones, external mic)
• LAN
• mini-PCIe slots (both wlan and wwan)
• Linux (through GRUB-as-payload)
• Windows (through GRUB-as-payload loading SeaBIOS image from disk; you have to use extracted VGA blob, dumped from memory isn't good enough)
• SD card slot
• Thermal management
• Fingerprint reader.
• Webcam
• Keyboard backlight
• Thinklight.
• bluetooth
• dock
• msata (fixed in commit c8f54a1109072706e2fa091dc9ab4ad3eb057b42)

Not tested:

• mini displayport (probably works)

Proprietary components status

• CPU Microcode (optional)
• ME(Management Engine) => you do not have to touch it (just leave it where it is)
• EC(Embedded Controller) => you do not have to touch it (just leave it where it is)

GPIO layout

This information should not be considered reliable in any way, shape or form

• GPIO57 - OUT - controls..

General Purpose Events layout

• GPE? - EC SCI
• GPE? - EC SMI

Flashing

Location of the SPI chips

T530 has 2 flash chips of 8M and 4M. They're concatenated to one virtual flash chip of 12M which is itself subdivided in roughly in 4 parts:

• Descriptor (12K)
• ME firmware (5M-12K)
• System flash (7M)

ME firmware is not readable. Vendor firmware locks the flash and so you need to flash externally (unless until someone figures out a way around it).

Proceeds as follows:

• Turn off your laptop, remove battery and AC adapter.
• Remove the keyboard.
• Connect your external SPI flasher to the top SPI chip which is under palm resting space, on left side of the board. It's a 4M chip. IF you've chosen CBFS_SIZE 4M or smaller that's the only chip you need to reflash.

I recommend using SOIC clip. Depending on the flasher you use, you may have to use separate 3.3V source. Make sure not to feed more than 3.3V ot the chip. I used buspirate as flasher and 3.3V power lines from another computer.

• Read the flash. Twice. Compare the files to be sure. Save a copy of it on

external media.

flashrom -p <yourprogrammer> -r flash.bin
flashrom -p <yourprogrammer> -r flash2.bin
diff flash.bin flash2.bin

If they don't match, do not proceed. If the file is 8M, you're flashing wrong chip, connect to the right one.

• Write the flash. Since you have to write only top 4M, first split out those 4M:

 dd of=top.rom bs=1M if=build/coreboot.rom skip=8

• Use flashrom to flash top.rom.

If you have trouble reading the chip successfully, the most common problems are

• insufficient power supply
• bad contacts
• too long wires
• bad pinout

The cable shipped with buspirate was too long, and needed to be trimmed.

See also In-System Programming