The wiki is being retired!

Documentation is now handled by the same processes we use for code: Add something to the Documentation/ directory in the coreboot repo, and it will be rendered to https://doc.coreboot.org/. Contributions welcome!

Introduction

The fallback mecanism permits to be able to use two different prefixes (normal/ and fallback/) for the romstage, ramstage and payload, in the same coreboot image.

The switch between the two prefixes can be governed by an nvram configuration parameter.

Prefixes

fallback/ is expected to hold the good known working image.

normal/ is expected to hold the image under test

Uses cases

Test new images way faster: if the image doesn't boot it will fallback on the old known-working image and save a long reflashing procedure
Test new images more safely: Despite of the recommendations of having a way to externally reflash, many new user don't. Assuming that the user don't screw up the fallback/ procedure (which adds a layer of complexity) he can test new images more safely because it will fallback on the known good image.
More compact testing setup: Since reflashing tools are not mandatory anymore, the tests can be done with less voluminous hardware, which means that the test setup is easier to bring with you while travelling.

Enabling the fallback switch

The Fallback switch behaviour is governed by the BOOTBLOCK_SIMPLE and BOOTBLOCK_NORMAL compilation options.

They are selectable in "Bootblock behaviour" in make menuconfig.

Currently only two choices are available:

BOOTBLOCK_SIMPLE: "(X) Always load fallback"
BOOTBLOCK_NORMAL: "(X) Switch to normal if CMOS says so"

If BOOTBLOCK_SIMPLE is chosen, then fallback/ , then no siwtch will ever be done and fallback/ will always be chosen, since this is the default we have to change it to get it to work. If BOOTBLOCK_NORMAL is chosen, then the switch will be able to work.

If the BOOTBLOCK_NORMAL is chosen, the functionality is disabled but can be enabled later if needed.

Make sure that in "General setup --->" you have:

(fallback) CBFS prefix to use

How it works (summary)

Coreboot will switch to fallback/ if the boot count is higher than CONFIG_MAX_REBOOT_CNT (or if normal/ isn't present).

Coreboot increments the reboot count at each boot.

Here, clearing the boot count is delegated to what is run after coreboot.

To get the maximum safety out of it, clearing the boot count after the last step of the boot is advised.

Example of use

For instance once the system is fully booted, a systemd unit can reset the boot count.

That way if the coreboot changes makes it impossible to boot a linux kernel or even if GNU/Linux can't fully boot, the boot count won't be reset.

Then the user will power off the computer, and at the next boot CONFIG_MAX_REBOOT_CNT will hopefully be reached. Then coreboot will boot on the good known working image and the boot will complete.

At that point the user is expected to reflash a good image in order not to go in normal/ again at the next boot.

Current limitations

scripts exist only for the systemd init system, but they are easy to adapt to other init systems
suspend/resume systemd scripts not written yet
some issues can arrise when the nvram layout is not the same between normal/ and fallback/
The number of failed boot is 3 by default (for all boards that don't set CONFIG_MAX_REBOOT_CNT)
In order to fully boot, some boards do reboot once during the boot procedure. The issue is that it reboot conditionally, and no code has been written yet to take that into account.
Payloads can have non-configurable default locations when loading things from cbfs:
- When using grub as a payload, grub.cfg is at etc/grub.cfg by default, so if you want to test grub as a payload, remember to change grub.cfg's path not to interfer with the fallback's grub configuration.
- Changing the path of what SeaBIOS loads from cbfs is probably configurable with SeaBIOS cbfs symlinks but not yet tested/documented with the use of the fallback mecanism

Using it with systemd

Prerequisites

Make sure that your fallback/ image has the fallback switch mecanism enabled
Build the fallback image as you would build an image usually

Building the normal/ image

Configuration

You need to set the following in "make menuconfig", before building a normal/ image:

[*] Update existing coreboot.rom image

And also set the prefix to normal/ in "General setup --->":

(normal) CBFS prefix to use

Then you will have to use a build script because of the shortcommings of coreboot's Kconfig build system.

build script

The build scrpit takes an existing coreboot image as argument.

That image is expected To have the fallback switch already enabled

#!/bin/sh
image="$1"
if [ $# -ne 1 ] ; then
	echo "Usage $0 <image>"
	exit 1
fi

die() {
  echo "Failed"
  exit 1
}

cbfs_remove() {
  file=$1
  ./util/cbfstool/cbfstool ./build/coreboot.rom remove -n ${file} 
}

cbfs_reuse_payload() {
  ./util/cbfstool/cbfstool ./build/coreboot.rom extract -f ./build/payload.elf -n fallback/payload
  ./util/cbfstool/cbfstool ./build/coreboot.rom add -f ./build/payload.elf -n normal/payload -t payload
}

make oldconfig || die
make clean || die
mkdir build/ || die

cp ${image} ./build/coreboot.rom || die

cbfs_remove normal/romstage
cbfs_remove normal/ramstage
cbfs_remove normal/coreboot_ram
cbfs_remove normal/payload
cbfs_remove config

# it now adds it automatically
cbfs_remove etc/ps2-keyboard-spinup

# comment if the .config has no etc/grub.cfg
# or if you don't want to update it
cbfs_remove normal/etc/grub.cfg
./util/cbfstool/cbfstool ./build/coreboot.rom add -f grub.cfg -n normal/etc/grub.cfg -t raw

make || die

#Re-add the same payload again
# cbfs_reuse_payload

./util/cbfstool/cbfstool ./build/coreboot.rom print

Example of use with systemd

The code dependencies can be found in gerrit

Mandatory configuration (in make menuconfig)

You will have to make two configurations:

one for the fallback image
one for the normal image

First image

start configuring the first image with:

make menuconfig

Then configure it like that:

Go in the following menu:

Architecture (x86)  --->

And then select that:

Bootblock behaviour (Switch to normal if CMOS says so)  --->

Which will bring that menu:

( ) Always load fallback
(X) Switch to normal if CMOS says so

Select the "Switch to normal if CMOS says so" line like described above.

In order to know if your computer booted correctly the last time, coreboot reads it in the nvram. There are two ways to make it know that it booted fine the last time:

The automatic way, which happens inside the ramstage of coreboot.
The manual way, which happens when you want after the ramstage.

If you want it to happen after the ramstage Select the following menu:

General setup  --->

And inside select the following if you want the manual way:

[*] Keep boot count

Or don't select it if you want the automatic way:

[ ] Keep boot count

Then choose the number of times you want it to try to boot, before switching back to fallback/

(1) Number of failed boot attempts before switching back to fallback/

Note that the minimum number could be device specific. Setting the minimum to 1 on the Lenovo x60 worked well.

In any case, make sure that you have:

(fallback-mode) Local version string
(fallback) CBFS prefix to use

Verify that you have the following in .config (that make menuconfig just generated if you followed the previous instructions correctly)

CONFIG_X86_BOOTBLOCK_NORMAL=y
CONFIG_BOOTBLOCK_SOURCE="bootblock_normal.c"

And that you have:

CONFIG_LOCALVERSION="fallback-mode"
CONFIG_CBFS_PREFIX="fallback"

If you selected "Keep boot count", also verify that you have:

CONFIG_KEEP_BOOT_COUNT=y

At the end copy the .config to defconfig-fallback (that will erase the file named defconfig-fallback if there was one):

cp .config defconfig-fallback

Second image

After configuring the first image, you should configure the second one. use "make menuconfig" again to change the current configuration in .config (you already copied it to defconfig-fallback, so you will only modify a copy of it).

make menuconfig

Then go in "General setup"

General setup  --->

And modify the prefix and the version string to look like that:

(normal-mode) Local version string
(normal) CBFS prefix to use

So that the second image that we will build later will be put in the "normal/" prefix and not in the "fallback/" one.

Then go in Architecture:

Architecture (x86)  --->

And enable the "Update existing coreboot.rom image" option:

[*] Update existing coreboot.rom image

At the end copy the .config to defconfig-normal (that will erase the file named defconfig-normal if there was one):

cp .config defconfig-normal

Pseudo-diff

Then compare the two resulting configurations to be sure of what you did:

$ diff -u defconfig-fallback defconfig-normal

The output should look a bit like that but with more context lines(the lines not starting with a "+" or a "-"):

--- defconfig-fallback	2013-10-26 22:27:19.471326092 +0200
+++ defconfig-normal	2013-10-26 22:26:44.471328732 +0200 
-CONFIG_LOCALVERSION="fallback-mode"
-CONFIG_CBFS_PREFIX="fallback"
+CONFIG_LOCALVERSION="normal-mode"
+CONFIG_CBFS_PREFIX="normal"
-# CONFIG_UPDATE_IMAGE is not set
+CONFIG_UPDATE_IMAGE=y

Compilation

Build script

This is a build script for the first build that will contains both /fallback and /normal:

#!/bin/sh
# In the cases where this work is copyrightable, it falls under the GPLv2
# or later license that is available here:
# https://www.gnu.org/licenses/gpl-2.0.txt

#verbose="V=1"

die() {
	echo
	echo "!!!! Compilation failed !!!!"
	exit 1
}

success() {
	echo
	echo "!!!! Compilation finished !!!!"
	echo
}

separator() {
	echo
	echo "!!!! First prefix compilation finished !!!!"
	echo
}

fallback() {
	make clean || die

	#fallback image
	cp defconfig-fallback .config  || die
	make ${verbose}  || die
	./build/cbfstool ./build/coreboot.rom add -f .config -n config-fallback -t raw  || die

	#because it could be re-included it in the second build...
	#./build/cbfstool ./build/coreboot.rom remove -n etc/ps2-keyboard-spinup  || die
	#./build/cbfstool ./build/coreboot.rom remove -n pci8086,109a.rom  || die
}


save_clean_and_restore_fallback() {
	cp ./build/coreboot.rom ./build-save/coreboot.rom.fallback || die

	make clean || die
	mkdir -p build/
	cp ./build-save/coreboot.rom.fallback ./build/coreboot.rom || die

	separator
}

normal() {
	#normal image
	cp defconfig-normal .config  || die
	make ${verbose} || die
	./build/cbfstool ./build/coreboot.rom add -f .config -n config-normal -t raw  || die

}

add_external_cbfs() {
	#Add the remaining files
	./build/cbfstool ./build/coreboot.rom add -f /home/gnutoo/x86/ipxe/src/bin/8086109a.rom -n pci8086,109a.rom -t raw || die
}

fallback
save_clean_and_restore_fallback
normal
add_external_cbfs
success

Update script

Before using that script, you should do:

make menuconfig #change the options if you need it, and save

And:

cp .config defconfig-normal-update

This script is meant for updating an existing coreboot.rom image while not touching the fallback/ part

#!/bin/sh
# In the cases where this work is copyrightable, it falls under the GPLv2
# or later license that is available here:
# https://www.gnu.org/licenses/gpl-2.0.txt

#verbose="V=1"

die() {
	echo
	echo "!!!! Compilation failed !!!!"
	exit 1
}

success() {
	echo
	echo "!!!! Compilation finished !!!!"
	echo
}

separator() {
	echo
	echo "!!!! First prefix compilation finished !!!!"
	echo
}

build_cbfstool() {
	make -C util/cbfstool
}
save_clean_and_restore_image() {
	if [ -f ./build/coreboot.rom ] ; then
		cp ./build/coreboot.rom ./build-save/coreboot.rom.fallback || die
	fi

	make clean || die
	mkdir -p build/
	cp ./build-save/coreboot.rom.fallback ./build/coreboot.rom || die

	separator
}

remove_normal_from_image() {
	./util/cbfstool/cbfstool ./build/coreboot.rom remove -n normal/romstage || die
	./util/cbfstool/cbfstool ./build/coreboot.rom remove -n normal/coreboot_ram || die
	./util/cbfstool/cbfstool ./build/coreboot.rom remove -n normal/payload || die
	./util/cbfstool/cbfstool ./build/coreboot.rom remove -n config-normal
}

normal() {
	#normal image
	cp defconfig-normal-update .config  || die
	make ${verbose} || die
	./util/cbfstool/cbfstool ./build/coreboot.rom add -f .config -n config-normal -t raw  || die

}

remove_external_cbfs() {
	./util/cbfstool/cbfstool ./build/coreboot.rom remove -n pci8086,109a.rom
}

re_add_external_cbfs() {
	./util/cbfstool/cbfstool ./build/coreboot.rom add -f /home/gnutoo/x86/ipxe/src/bin/8086109a.rom -n pci8086,109a.rom -t raw || die
}

build_cbfstool
save_clean_and_restore_image
remove_normal_from_image
remove_external_cbfs
normal
re_add_external_cbfs
success

Use it

If you chose the following option:

 [*] Keep boot count

Then you or something will need to tell coreboot that the computer booted correctly. Here are some example scripts.

set-fallback-1.sh

#!/bin/sh
nvramtool -w boot_option=Fallback
nvramtool -w last_boot=Fallback
nvramtool -w reboot_bits=1

set-normal-0.sh

#!/bin/sh
nvramtool -w boot_option=Normal
nvramtool -w last_boot=Normal
nvramtool -w reboot_bits=0

get-nvram.sh

#!/bin/sh
nvramtool -a | grep -e boot_option -e last_boot -e reboot_bits

Systemd units

/etc/systemd/system/coreboot-booted-ok.service:

#  This file is not part of systemd.
#
#  this file is free software; you can redistribute it and/or modify it
#  under the terms of the GNU Lesser General Public License as published by
#  the Free Software Foundation; either version 2.1 of the License, or
#  (at your option) any later version.

[Unit]
Description=Tell coreboot that the computer booted fine.
DefaultDependencies=no
Wants=display-manager.service
After=display-manager.service

[Service]
Type=oneshot
RemainAfterExit=yes
ExecStart=/usr/local/sbin/nvramtool -w boot_option=Normal
ExecStart=/usr/local/sbin/nvramtool -w last_boot=Normal
ExecStart=/usr/local/sbin/nvramtool -w reboot_bits=0

[Install]
WantedBy=multi-user.target

Update build script

#!/bin/sh

if [ $# -ne 1 ] ; then
  echo "Usage $0 <image>"
  exit 1
fi

image="$1"

die() {
  echo "Failed"
  exit 1
}

cbfs_remove() {
  file=$1
  ./util/cbfstool/cbfstool ./build/coreboot.rom remove -n ${file} 
}

make oldconfig || die
make clean || die
mkdir build/ || die

cp ${image} ./build/coreboot.rom || die

cbfs_remove normal/romstage
cbfs_remove normal/coreboot_ram
cbfs_remove normal/payload
cbfs_remove config
cbfs_remove etc/grub.cfg

make || die

Fallback mechanism