Board:kontron/986lcd-m

Top

Side

Backpanel

Board and power supply

This page describes how to use coreboot on the Kontron 986LCD-M/mITX mainboard. It is maintained by Uwe Hermann.

Status

Device/functionality	Status	Comments
CPU
CPU works	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Intel(R) Core(TM)2 CPU T5300 @ 1.73GHz (dual core)
L1 cache enabled	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	CPU: L1 I cache: 32K, L1 D cache: 32K
L2 cache enabled	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	L2 cache: 2048K
L3 cache enabled	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Multiple CPU support	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Multi-core support	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Both cores show up in /proc/cpuinfo.
Hardware virtualization	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested	Hardware virtualization is not supported by this CPU. Doing modprobe kvm-intel yields kvm: no hardware support (coreboot + vendor BIOS).
RAM
EDO	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
SDRAM	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
SO-DIMM	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
DDR	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
DDR2	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Works fine, but currently you need to populate both RAM slots with DIMMs (of the same size?).
DDR3	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Dual channel support	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
ECC support	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | ?
On-board Hardware
On-board IDE 3.5"	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
On-board IDE 2.5"	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board SATA	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Tested: SATA disk (hda1 in FILO, /dev/sda1 in Linux), but you currently have to use pci=noacpi.
On-board SCSI	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board USB	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Tested: USB thumb drive in all 4 backpanel USB ports, as well as on the USB pin headers on the board (USB6_7, see manual).
On-board VGA	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	You need to prepend the VGA blob from the proprietary BIOS for this to work. Console works, X11 works (use the intel X.org driver).
On-board Ethernet	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	The eth1 interface (in this case) works fine, but so far ifconfig -a only shows one of the three NICs (?)
On-board Audio	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	Doesn't seem to work, yet.
On-board Modem	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board FireWire	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested
On-board Smartcard reader	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board CompactFlash	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	There's an onboard CompactFlash slot on the back-side of the board. FILO sees it as (hd2,0) / hdc1, Linux as /dev/sdb1.
On-board PCMCIA	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board Wifi	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board Bluetooth	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
On-board SD card reader	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Add-on slots/cards
ISA add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Audio/Modem-Riser (AMR/CNR) cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	Doesn't seem to work properly (at least not with pci=noacpi). A tested PCI NIC appears in ifconfig -a but does not work.
Mini-PCI add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Mini-PCI-Express add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
PCI-X add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
AGP graphics cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x1 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x2 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x4 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x8 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
PCI Express x16 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	Doesn't seem to work (at least not with pci=noacpi). A tested PCIe VGA card doesn't appear in lspci,
PCI Express x32 add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
HTX add-on cards	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Legacy / Super I/O
Floppy	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | ?
Serial port 1 (COM1)	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Serial port 2 (COM2)	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | ?
Parallel port	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Doing modprobe ppdev works, but no further test were performed.
PS/2 keyboard	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
PS/2 mouse	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
Game port	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Infrared	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | ?
PC speaker	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK
DiskOnChip	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Input
Trackpoint	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Touchpad	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Fn Hotkeys	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Fingerprint Reader	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Laptop
Docking VGA	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking LAN	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking USB	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking Audio	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Docking Displayport	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Thinklight	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Webcam	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Miscellaneous
Sensors / fan control	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Works fine using the w83627hf, coretemp (and also i2c-dev, i2c-i810, and eeprom) Linux kernel modules.
Hardware watchdog	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Not yet actually tested, but it seems to be found: iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0560).
SMBus	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | ?
CAN bus	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
CPU frequency scaling	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	Needs ACPI. With pci=noacpi the cpufreq-info utility doesn't output anything useful. On vendor BIOS you can use p4-clockmod (discouraged) or acpi-cpufreq (iff you enabled the respective option in the BIOS menu).
Other powersaving features	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
ACPI	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	There's a (partial?) ACPI implementation for this board, but it may need further testing/fixing.
Reboot	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Seems to work fine, even with pci=noacpi.
Poweroff	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | WIP	Needs ACPI, thus won't work if you use pci=noacpi.
Suspend	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Nonstandard LEDs	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
High precision event timers (HPET)	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	The HPET is detected by Linux (hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0) and powertop output suggests that it works ok.
Random number generator (RNG)	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Wake on modem ring	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A
Wake on LAN	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested	The board supports WOL (tested with vendor BIOS using the wakeonlan utility).
Wake on keyboard	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Untested	Works fine with vendor BIOS.
Wake on mouse	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | N/A	Doesn't seem to be supported (by the hardware / vendor BIOS), tested with a PS/2 mouse, as well as with a USB mouse.
TPM	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | Unknown
Flashrom	OK=lime | TODO=red | No=red | WIP=orange | Untested=yellow | N/A=lightgray | yellow }}" | OK	Works fine, but you have to use -m kontron:986lcd-m when booted with the vendor BIOS (not needed when booted with coreboot).

Build tutorial

$ svn co svn://coreboot.org/repos/trunk/coreboot-v2
$ cd coreboot-v2/targets
$ ./buildtarget kontron/986lcd-m
$ cd kontron/986lcd-m/kontron_986lcd_m

Now copy your payload into the current directory and name it payload.elf. Then:

$ make -s

The resulting coreboot.rom is your coreboot ROM image you can flash using flashrom.

Notes

• If you use FILO, SATA will probably be hda and hdb, while hdc is the master drive of the IDE controller.
• Currently you have to use pci=noacpi on the kernel command line to make IDE and SATA work.
• If you experience kernel crashes (when building without onboard VGA support) try to blacklist the agpgart and intel_agp kernel modules.
• TODO: Add notes for proper (onboard) VGA setup.

I, the copyright holder of this work, hereby release it into the public domain. This applies worldwide. In case this is not legally possible: I grant anyone the right to use this work for any purpose, without any conditions, unless such conditions are required by law.