Uploads by Linux junkie
Jump to navigation
Jump to search
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 03:03, 28 June 2010 | Paraflashersch.jpg (file) |  |
521 KB | New design | 2 |
| 03:01, 30 March 2009 | Foil-hgun11.jpg (file) |  |
749 KB | 11. Close up of the chipless board. Now your ready to clean it up and solder on a socket. | 1 |
| 03:00, 30 March 2009 | Foil-hgun10.jpg (file) |  |
760 KB | 10. Another shot of the foil and chip. | 1 |
| 02:59, 30 March 2009 | Foil-hgun9.jpg (file) |  |
672 KB | 9. Shot with the foil and chip removed. | 1 |
| 02:58, 30 March 2009 | Foil-hgun8.jpg (file) |  |
892 KB | 8. After a minute or two the chip will pretty much fall off. Use tweezers to remove. | 1 |
| 02:55, 30 March 2009 | Foil-hgun7.jpg (file) |  |
866 KB | 7. Blow the heat at an angle to the side of the chip at the solder joints going around the chip in a circle. Never directly on top. | 1 |
| 02:53, 30 March 2009 | Foil-hgun6.jpg (file) |  |
830 KB | 6. Close up of foil over chip. | 1 |
| 02:52, 30 March 2009 | Foil-hgun5.jpg (file) |  |
955 KB | 5. Place the foil over the chip. | 1 |
| 02:51, 30 March 2009 | Foil-hgun4.jpg (file) |  |
898 KB | 4. Foil with chip cut out. | 1 |
| 02:49, 30 March 2009 | Foil-hgun3.jpg (file) |  |
840 KB | 3. Cut out a rectangle out just the size of the chip. | 1 |
| 02:47, 30 March 2009 | Foil-hgun2.jpg (file) |  |
926 KB | 2. Bend the foil over the chip for cut out lines. | 1 |
| 02:44, 30 March 2009 | Foil-hgun1.jpg (file) |  |
911 KB | 1. Use a piece of aluminum foil and fold it in half (for double the protection) | 1 |
| 13:12, 12 February 2009 | Paraflasher front.jpg (file) |  |
369 KB | Front picture of the paraflasher | 1 |
| 13:09, 12 February 2009 | Paraflasher left.jpg (file) |  |
376 KB | Left picture of the paraflasher | 1 |
| 13:08, 12 February 2009 | Paraflasher right.jpg (file) |  |
376 KB | Right picture of the paraflasher | 1 |
| 13:05, 12 February 2009 | Paraflasher bottom.jpg (file) |  |
412 KB | Ugly bottom picture of the paraflasher | 1 |
| 13:04, 12 February 2009 | Paraflasher top.jpg (file) |  |
388 KB | Top picture of the paraflasher | 1 |
| 13:01, 12 February 2009 | Paraflasher.jpg (file) |  |
442 KB | This is my first build of the paraflasher. | 1 |
| 02:55, 28 November 2008 | SN74CBTD3861.jpg (file) |  |
14 KB | SN74CBTD3861 | 1 |
| 20:16, 24 November 2008 | M74HC244B1R.jpg (file) |  |
31 KB | M74HC244B1R | 1 |
| 17:20, 16 May 2008 | Rm4100 rear.jpg (file) |  |
229 KB | Back of the RCA RM4100 | 1 |
| 17:18, 16 May 2008 | Rm4100 front.jpg (file) |  |
590 KB | Front of the RCA RM4100 | 1 |
| 17:09, 16 May 2008 | Ip1000 board.jpg (file) |  |
211 KB | Thomson IP1000 Board still in the case | 1 |
| 17:07, 16 May 2008 | Ip1000 rear.jpg (file) |  |
462 KB | Back of Thomson IP1000 | 1 |
| 17:05, 16 May 2008 | Ip1000 front.jpg (file) |  |
585 KB | Front of Thomson IP1000 | 1 |
| 22:55, 12 March 2008 | Rca rm4100 mods.jpg (file) |  |
268 KB | RM4100 with PLCC Socket, IDE, & VGA Mods that is used fro development. | 1 |
| 22:51, 12 March 2008 | Rca rm4100.jpg (file) |  |
216 KB | Stock RM4100 | 1 |
| 22:50, 12 March 2008 | Rca rm4100 modded.jpg (file) |  |
268 KB | RM4100 with PLCC Socket, IDE, & VGA Mods that is used fro development. | 2 |
